- Toronto Special Order
- Ottawa Special Order
- Mississauga Special Order
- Calgary Special Order
- Edmonton Special Order
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer used in the internationally renowned RØDE NT5. The capsule is designed to attach to a custom made, multi-position swivel mount allowing it to be independently positioned with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4" to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar® fibre reinforced cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television, Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in RØDE's design and manufacturing facility in Sydney, Australia. Utilising state of the art computer controlled machining and assembly technologies, RØDE is able to achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar® fibre reinforced cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
Frequency range:40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
- 1/2” (externally biased) gold sputtered true condenser capsule
- Heavy duty satin-nickel-plated body
- 2-position variable pad: 0 dB and -10 dB
- 2-position variable high-pass filter: flat and 80 Hz
- Surface mount technology
- Low noise
- Wide dynamic range
- Full frequency response
- Supplied complete with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch
- Designed & manufactured in Australia
- Full 2 year guarantee
|Operation Power||The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector.|
|Operation Output Impedance||The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this is used, the output signal level will be reduced. The NT6 output is balanced between pin 2 (hot) and pin 3 (cold). Pin 1 is ground.|
|Acoustic Principle||Externally polarised 1/2" (13mm) pressure gradient condenser|
|Frequency Range||40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave|
|Output Impedance||200 Ω|
|Signal noise ratio DIN/IEC 651||75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)|
|Equivalent Noise||19 dB SPL (per IEC651, IEC268-15)|
|Maximum SPL||138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum|
|Sensitivity||-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB|
|Dynamic Range - DIN/IEC 651||119 dB (per IEC651, IEC268-15)|
|Power Supply Voltage||48 Volts (P48)|
|Weight||386 grm. (12.41 oz.)|
Diameter = Ø 20 mm
Length = 118.4 mm
Main Body Assembly:
Diameter = Ø 20 mm
Length = 88.5 mm (Capsule face to cable connector)
Height = 64 mm (Capsule to mount)
|Maximum Output Voltage||6 dBu (@ 1% THD into 1 kΩ)|
|Pin Assignment||3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)|
Questions & Answers
Rode Microphones NT6 Compact Condenser Microphone
Looking for a personal touch? Not sure if you are choosing the right product? Our staff is here to help.
We want to make sure you get the right product for your needs.
Our staff will help you understand the options available so you can be confident in your purchase.
As the country’s leading Professional Imaging retailer, Vistek is in the perfect position to ensure you make the right choice.
Contact us today for a personal touch.