• Webcode: 433944 • Mfr: 258100
Product Highlights
  • Sony Venice Compatibility
  • 2x 3-Pin Fischer / 2x 2-Pin LEMO / 2x D-Tap / 4-Pin XLR Connection
  • 484 g (17 oz) Weight
  • 3.1 x 11.4 x 13.3 cm (1.5 x 4.5 x 5.2") Dimensions
  • Durable & lightweight
Web Availability: Special Order
Vistek Locations
  • Toronto Special Order
  • Ottawa Special Order
  • Mississauga Special Order
  • Calgary Special Order
  • Edmonton Special Order
Please call and verify availability at the store as stock changes daily.

Lease this for: $64.96 Learn More


D-Box (Sony Venice, Gold Mount)

D-Box (Sony Venice , Gold Mount) is a custom version of Wooden Camera's popular D-Box that adds power distribution, standardized remote start/stop and hot swap abilities for the Sony Venice camera. The D-Box main unit attaches to the back of the AXS-R7 or to the V-Mount plate on the camera rear and the Power Strip portion attaches to the top right side of the camera via a 3pin Fischer and the tape hook threaded hole.

Connectors on the D-Box Power Strip are contoured to match the camera profile and connector angle which allows for all cables to be installed with no collisions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port including the ARRI UMC-4 / WCU-4.

The DC input on the D-Box is the same as the camera's 4pin XLR connector allowing for an AC power supply, external power plate or VCLX block battery to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the onboard battery fully charged.

Physical fuses have been replaced by a processor controlled amp limit which is settable to 3.8, 5.8, or 9 amps using the slide switch on the operator's side. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. 

The "DC IN" and "BATT" LEDs are dual LEDs. This means the LED If battery voltage is above 12.5V the LED will be green. If the battery voltage is below 12V the LED will be red. If the battery voltage is between those values the LED will be orange (red + green). Flashing may occur during phase transition. Highest quality Anton Bauer components are used in the Gold Mount assembly and the unibody power plate design is both extremely durable and lightweight.


  • Gold Mount Power Plate
  • 2x 3pin Fischer at 24V with Run Stop
  • Regulator built in to convert battery voltage to 24V
  • Maximum 3A surge, 2.5A sustained shared between connectors
  • 2x 2pin LEMO at 12V unregulated
  • ARRI standard wiring
  • 2x D-Tap at 12V unregulated
  • 5V USB
  • 4pin XLR DC Input
  • Hot swappable with on board battery
  • Capable of providing power to accessories and camera without brick battery attached

*Connectors used in this assembly are not manufactured by LEMO but are made to the same specifications and are LEMO compatible.


Product Specifications

D-Box (Sony Venice, Gold Mount)

Compatibility Sony Venice
Connection 2x 3-Pin Fischer / 2x 2-Pin LEMO / 2x D-Tap / 4-Pin XLR
Weight 484 g (17 oz)
Dimensions 3.1 x 11.4 x 13.3 cm (1.5 x 4.5 x 5.2")

Questions & Answers

Wooden Camera D-Box (Sony Venice, Gold Mount)

Looking for a personal touch? Not sure if you are choosing the right product? Our staff is here to help.

We want to make sure you get the right product for your needs.
Our staff will help you understand the options available so you can be confident in your purchase.

As the country’s leading Professional Imaging retailer, Vistek is in the perfect position to ensure you make the right choice.
Contact us today for a personal touch.